Author Topic: 99-00 civic si cluster swap into 88-91 crx  (Read 5520 times)

0 Members and 2 Guests are viewing this topic.

Offline Thundercat

  • Duh, Winning!
  • Global Moderator
  • Steppin' it up!
  • *****
  • Join Date: May 2009
  • Posts: 2416
  • Karma: 124
  • Tuck'd & Swap'd

  • Activity
    0%
    • Your lookin at it
99-00 civic si cluster swap into 88-91 crx
« on: October 22, 2010, 09:47:11 am »

I got this DIY write-up from XjamesX on CR-XC I saw it and thought it would be a good idea to spread it




Well here is a write up on how to install a 99-00 civic Si cluster in your EF. I installed it in my 91 CRX si. All the wiring is done for a 90-91 Crx. The wiring is the same for 90-91 civic hatches. The fitment may be a little different in hatches but should work. I am getting mixed feedback about the wiring for 88-89 models, I am not 100% positive if the wiring is the same but I will have it figured out shortley and will add the 88-89 wiring when finished.

OK 88-89 wiring is added. The wire colors are the same but the pin placement s are different . I added clip pictures and a chart for the 88-89 crx/civics. Another thing you will have to change is the dimmer switch clip for the 90-91 cluster hood. Just swap the 88-89 clip with the 90-91 clip. The wire colors are the same so just match up the wires and it will work

Here is a list of things needed to comlete the swap.

Tools:

10mm socket ( to unbolt speedo)
philips head screw driver
wire cutters
soldering iron
electrica l tape

Items needed:

96-00 Civic cluster Si, EX, DX, HX whichever you want to use. I chose the Si because it looks cool.
Cluster clips that plug into the civic cluster. With some wire attached the more the better
Any electroni c speedo from 92 and up civic or 94 and up integra.
Clip that plugs on top of the speedo also with some wire

The only things needed to be modified to fit the cluster into the dash where the metal tabs inside the cluster bowl. Just unscrew them and there is plenty of room. As far as bolting it down it is in pretty tight and takes some shifting to get the cover over the cluster but when it is in it is tight. I have been driving the car for a few weeks now and it didn't vibrate or shift in any way. If you wanted to screw it in you could drill some holes into the roof of the gauge cover and put screws through it into the tabs on the civic cluster but it is not necessary .







Here is the wiring. The blue clips are for the civic and the grey are the crx. You need to wire in the blue clips in place of the grey ones. The red X's mean the wire is no
t used. 11 of the 17 wires match up in color and have the same function. Look at the last chart and you will see what I mean.











88-89 clips






90-91 wiring color chart




88-89 wiring color chart



VSS installat ion:

Pull the cover up over the cable on the VSS then push the retaining clip off of the cable and pull the cable out of the Vss. Then take the 10mm socket and your rachet and unbolt the cable driven Vss from the tranny. I also used 3/8 15" extension and a swivel head to get the 10mm bolt out.






Here is the cable driven Vss from my crx (note I have a b16 and your cable Vss may look different .



This is a pic of a 99 civic Vss I stole from my sisters car for picture purposes. This Vss will work fine.




here is a pic of the VSS I used. The black part is from a 99 integra and the bottom part is from a 92 civic Si. These 2 parts work fine together. I ordered the metal piece from honda for $39 and the black piece used for $35. I stole the gear out of my sisters civic and it works with the teg/civic combo Vss I used. I also ordered new O-ring seals for the VSS just to be on the safe side. Those where about $5 total.



This is the connector you will need that plugs onto the electroni c Vss. I didn't have one So I just plugged wires directly onto the VSS and sealed them up.



Next just slip the electroni c VSS into the tranny and bolt up with the 10mm bolt. Now here is the wiring, I don't have pics of the prosses but it is easy to understan d. There are 3 wires coming out of the VSS plug. Power, signal and ground. The power wire you have to run to a switched power source, pin B4 and A15 on the civic clips will work fine. The ground wire you just have to ground, splice it into an exsisting ground or create a new one either will work. The signal wire has to be split into 2. Run one signal into the back of the cluster in pin A11, The other into Pin B16 on the ECU. You split the signal because both the cluster and Ecu need the Vehicle speed signal.

ADDED: signal wire diagram.



Here are some pics of it installed and working. Sorry the night pic didnt come out very well but you get the idea.





ECEFC is not responsib le for any damages that may be caused by this swap. Enjoy
« Last Edit: October 22, 2010, 09:51:34 am by Thundercat »
~CREW LEGIT~JJ AUTOWERKS
~IMPORTALLIANCE.ORG~All IN FAB~BISIMOTO~

Offline HONGO aka Shroomz

  • n00b
  • Join Date: Apr 2015
  • Posts: 2
  • Karma: 0

  • Activity
    0%
Re: 99-00 civic si cluster swap into 88-91 crx
« Reply #1 on: April 30, 2015, 11:34:32 pm »
I don't see the pics. Plz help. This is the only thread I could find that brakes it down clearly. Thanks

Offline rbwdriven

  • Administrator
  • Steppin' it up!
  • *****
  • Join Date: May 2009
  • Posts: 5489
  • Karma: 63

  • Activity
    0%
Re: 99-00 civic si cluster swap into 88-91 crx
« Reply #2 on: May 02, 2015, 09:48:23 am »
I know it can be done cause my mate used the thread and he has a 97 prelude cluster in his ef.


 

Related Topics

  Subject / Started by Replies Last post
4 Replies
3955 Views
Last post June 17, 2010, 08:08:23 pm
by Whosthisguy
4 Replies
1194 Views
Last post January 25, 2011, 05:10:11 pm
by EFJames
7 Replies
1441 Views
Last post January 27, 2011, 11:05:49 pm
by Todubbled1
14 Replies
2358 Views
Last post April 04, 2011, 08:55:02 pm
by rbwdriven
2 Replies
5562 Views
Last post September 09, 2012, 12:28:17 pm
by bigdare23